Learn / The SIDRA model / Article

What is good about analytical traffic modelling?

The power of analytical models in traffic management and design. Why traffic modellers use analytical models for planning, management, design and operations, and a warning about decisions made from watching microsimulation animations without auditing their analytical soundness.

Dr Rahmi Akçelik has published a report presenting a brief discussion of why traffic modellers use analytical models for traffic and transport planning, management, design and operations purposes.

The applications include traffic impact analysis, roundabout geometric design, efficient operation of traffic signal control systems and development of balanced Movement and Place solutions. Analytical models enhance the productivity of transport planners and traffic engineers by allowing them to analyse more scenarios with less effort. They are also used for verification and calibration of various aspects of microsimulation models.

Analytical models are based on a scientific approach and are capable of modelling intersections, interchanges, freeways, rural roads, urban streets and networks with complex traffic conditions. They provide unique value to transport planning and traffic engineering decision-making through balanced solutions that consider the conflicting needs of all transport users, including pedestrians, cyclists, buses, tram / light rail, cars and freight vehicles. This provides significant cost savings and environmental benefits.

Some technical issues in the use of microsimulation models are explained as a warning against decision making on the basis of limited viewing of animations generated by microsimulation runs without auditing their analytical soundness.

This page is an extract from the full publication on the SIDRA SOLUTIONS publications site: View publication

What is an analytical model?

An analytical model is

  • An engineering approach.
  • Algorithmic.
  • A combination of theoretical and empirical approaches.e.g. Performance estimation based on queuing theory with formulations calibrated using established (well specified) survey techniques.
  • Auditable. It allows in-depth questioning of model assumptions.

What can an analytical model do?

An analytical model can

  • Calculate.
  • Find solutions.
  • Estimate capacity as a basic parameter that determines traffic performance (see Section 3.1).
  • Optimise traffic performance.
  • Optimise traffic signal phasings and timings.
  • Quantify the effect of pedestrians on signal timings and vehicle movement capacity.
  • Contribute to traffic modelling as part of a Movement and Place approach.With extensive pedestrian modelling and detailed modelling of vehicle movement classes including cyclist, bus, tram / light rail and large truck, SIDRA is ideal in relation to the “Movement” aspect of this, even where “Place” is more important than “Movement”.
  • Model CO2 emissions for environmental assessments.The SIDRA power-based fuel and emissions models can estimate emissions of traffic movements, in particular CO2, with great accuracy.
  • Provide consistent modelling of different intersection types by using algorithms that employ consistent methods.SIDRA capacity and performance models provide a unique consistent approach for different types of signalised and unsignalised traffic facilities.
  • Predict and assess conditions that cannot be seen in “animation”.e.g. Delay to vehicles departing from the queue after the modelling period under oversaturated conditions (see Section 3.2).

Powerful concepts and model parameters

Powerful concepts and model parameters used by analytical models are well-established, are understood by the profession, and provide a common language for communication. They are useful in assessing traffic conditions and for signal timing analysis, including analysis for actuated signal control. They can also be used for verification and calibration of various aspects of microsimulation models (Yoshii 1999).

These concepts and model parameters include

  • CapacitySee Section 3.1
  • Degree of saturationDemand flow / capacity ratio
  • Saturation flowQueue discharge flow rate
  • Critical gap and follow-up headwayFor gap acceptance processes
  • Percentile queue lengthAnd probability of blockage by downstream queues
  • Flow, speed, density and spacingFundamental relations among them
  • SCATS MF and detector occupancyParameters used by traffic signal control systems
  • BunchingRandom moving queues in an uninterrupted stream
  • PlatoonsVehicles departing from signalised intersections

These concepts and parameters have been developed and used in traffic modelling and control for a long time. They include key parameters used in analytical model calibration.

“Traffic” vs “individual vehicles”

The concepts and parameters listed above are for “traffic streams” or “traffic movements”. This is a modelling approach that converts “individual vehicle” movement characteristics such as car following, lane change, acceleration and deceleration to more aggregate and measurable “traffic” characteristics. This provides the capabilities listed above. For information about the level of detail in analytical models, see Section 3.4.

Workflow

Analytical models are less costly than microsimulation to use, providing workflow efficiencies as they:

Workflow efficiencies

  • Are easier to set up. Low model specification time due to clarity of concepts.
  • Are quicker to run. Quicker solutions.
  • Reduce modelling times by helping the modeller to spend less time on setting of key parameters.
  • Help modellers to analyse a large number of scenarios (alternative solutions, existing and development conditions, design life analysis for future traffic conditions) and make decisions about recommended solutions with less effort.
  • Can be reviewed (audited) to assess whether calibration of key model parameters has produced realistic results, as listed above.

Analytical models offer a more stable answer

Analytical models offer a more stable answer compared with microsimulation model results, which vary due to randomness and depend on the number of simulation runs.

Understanding and dealing with uncertainty and sensitivity of solutions to model parameters is important.

Uncertainty

  • Finding a reliable solution representing average and percentile values of performance variables would require a large number of simulation runs with long simulation periods for convergent solutions.
  • Analytical models are not “deterministic” as is claimed sometimes. They use queuing theory for random overflow and persistent oversaturation (congestion). See Section 3.1.
  • For oversaturated conditions, simulation cannot be run for longer periods for convergence since queues build up persistently with longer periods because of demand exceeding capacity. An increased number of simulations is needed rather than longer simulations for this reason.
  • For near-saturated conditions, when the average demand is less than but close to capacity, significant overflow queues occur due to randomness of arrival flows. Therefore, average results require a large number of simulations. Figure 1 shows the difference between average values of two simulation points for low and high degrees of saturation.This is important since the effect of randomness in arrival flow rates is highest near capacity conditions, and furthermore, the capacity values can also change cycle by cycle. This shows the difficulty of obtaining performance estimates representing average conditions from microsimulation modelling. See the discussions in Sections 3.1 and 3.2.
  • For convergent solutions, downstream queue blockage effects resulting in capacity losses by upstream movements need an increased number of iterations for analytical models and an increased number of simulations by microsimulation models (especially if downstream queue blockage causes oversaturation).

Sensitivity

The sensitivity of performance variables (delay, queue, stop, etc.) is much higher at high degrees of saturation due to the nonlinearity of the performance function, as seen in Figure 1.

Figure 1 - Non-linear characteristic of traffic performance Performance Delay · Queue · Stops · Cost · Travel time Degree of saturation Demand flow ÷ Capacity Error in the average value Nonlinearity makes it more difficult to find the average value at high degrees of saturation
Figure 1Non-linear characteristic of traffic performanceFrom the full publication. Redrawn as vector for the web.

Ongoing development of models

Existing analytical models get improved, and models are developed for new areas of transport practice as traffic science discovers laws applicable to traffic movements.

Conclusion

Better knowledge and understanding

Analytical models facilitate better knowledge and understanding of the laws that rule traffic movements.

As distinct from, but based on, the behaviour of individual vehicles and their relationships, and the interactions of those movements in a complex traffic system.

Watching an animation, even if it is a perfect replication of the real-life conditions, does not reveal those laws to a modeller who does not have adequate knowledge based on concepts developed by decades of traffic science.

It is also uncertain whether an animation based on a single simulation run would represent the traffic conditions of a scenario, given the variations among many simulation runs necessary for oversaturated and near-saturated traffic conditions (refer to Figure 1).

No model is perfect

It is important to understand the model and know its limitations. An analytical model user with knowledge and expertise can question the model assumptions and address areas of concern more readily because of the conceptual strength of the model.

Expert use of traffic models with high levels of knowledge and understanding will be even more important as Artificial Intelligence (AI) threatens to take over the decision-making process in the traffic planning, design and operations processes, as in other professions.

Acknowledgements

The author thanks his colleagues Mark Besley, Ian Espada, Vince Taranto, David Nash and Nagui Rouphail for their valuable comments on this document.

References

  1. TRB (2022). Highway Capacity Manual Edition 7. Transportation Research Board, National Research Council, Washington, DC, USA, 2022.
  2. AKÇELIK, R. and BESLEY, M. Microsimulation and Analytical Methods for Modelling Urban Traffic. Paper presented at the Conference on Advance Modelling Techniques and Quality of Service in Highway Capacity Analysis, Truckee, California, USA, 2001.
  3. AKÇELIK, R. Microsimulation and Analytical Models for Traffic Engineering. Presentation at the ARRB - AUSTROADS Microsimulation Forum, 19-20 September 2007.
  4. DoT Victoria. Movement and Place in Victoria. Department of Transport, Melbourne, Victoria, 2019.
  5. TfNSW. Design of roads and streets - A guide to improve the quality of roads and streets in NSW (Movement and Place). Transport for NSW, NSW Government, 2023.
  6. IPWEAQ. Street Design Manual: Walkable Neighbourhoods (Parts 1 to 3). Institute of Public Works Engineering Australasia, Queensland, 2020.
  7. AKÇELIK, R., BESLEY, M., ESPADA, I. and NASH, D. Management of traffic modelling - a critique of Austroads Report AP-R621-20 (Transport modelling for project managers), 2nd Edition. Technical Note. Akcelik & Associates Pty Ltd, Melbourne, Australia, 2021.
  8. YOSHII, T. (1999). Standard Verification Process for Traffic Simulation Model - Verification Manual. Draft Report. Kochi University of Technology, Kochi, Japan.
SIDRA INTERSECTION 11

Analytical modelling, lane by lane.

Consistent capacity and performance models for every intersection type
Signals · Roundabouts · Sign control · Networks · Included: SIDRA ASSIGN

Explore the features